Inline injection and batch tanks, compared
The short answer
Inline injection doses concentrate into the water as it flows, so solution is made continuously and on demand. Batch tanks mix a full volume in advance, hold it, and feed from it. Injection is cheaper, takes less floor space and suits a facility running one recipe; it also gives you no tank of solution to test before it reaches a plant. Batch tanks cost more in equipment, pumps and room, and in exchange let you verify every batch, run different recipes to different rooms on the same day, and keep feeding if the injection side fails. Larger multi-room facilities tend to end up with batch tanks for that reason.
What each one actually does
Inline injection puts a proportional injector in the water line. Water flowing through it draws a fixed ratio of concentrate from a stock container, and solution exists only while water is moving. There is no reservoir of mixed feed anywhere in the system.
Batch mixing fills a tank with water, doses it to a target, mixes and holds it, then feeds the room from that tank with its own pump. Solution exists as a known volume you can sample before a plant ever sees it.
| Inline injection | Batch tanks | |
|---|---|---|
| Solution exists | Only while water flows | As a held volume |
| Can you test before feeding | No, you test what came out | Yes, you test the tank |
| Recipes at one time | One per injector line | One per batch tank |
| Floor space | Small, a skid and stock containers | Large, tanks plus access around them |
| Equipment count | Injector, stock containers, filtration | Tanks, pumps, recirculation, drains, master valves |
| If the dosing side fails | Feeding stops | Feed continues from what is in the tank |
| Response to a recipe change | Immediate | Next batch |
What the drawing tells you
You can tell which method a set uses without reading a word of the specification. A batch system shows tanks with a pump, a recirculation line, a drain and a master valve on each. The sample P&ID has six of them at 300 gallons. An injection system shows a skid in the line with stock containers beside it and no held volume anywhere downstream.
A set can carry both. The sample approval set has a Dosatron sheet for inline injection and a P&ID built on batch tanks, because different parts of a building are fed differently. Propagation and mothers often run injection, while flower runs batch.
Where each one wins
Injection suits
- One recipe across the whole facility, or one per zone group.
- Buildings where water room floor space is tight, which is most retrofits.
- Operations that change recipe often and want the change to land immediately.
- Smaller facilities where the cost of six tanks, six pumps and the plumbing between them is not justified.
Batch tanks suit
- Multi-room facilities running different rooms on different feeds on the same day.
- Operations that test every batch before it reaches a plant, which is most of the ones chasing consistency.
- Buildings where a dosing fault stopping irrigation would be expensive, since a full tank keeps feeding.
- Crop steering programmes, where a known volume at a known EC is the unit of control.
What batch tanks actually cost you in equipment
On the sample P&ID each of the six batch tanks carries its own batch tank pump, a recirculation valve, a drain valve and a master valve, plus the fill side from the fertigation skid. That is five pieces of equipment per tank before the tank itself, and thirty across six tanks.
That is the real cost difference, and it is also why the water room gets six sheets of its own in a detail set. If floor space and that equipment count are not available, injection is not a compromise, it is the correct answer for that building.
Common questions
What is the difference between inline injection and batch tank fertigation?
Inline injection doses concentrate into flowing water, so solution exists only while irrigation runs. Batch tanks mix and hold a known volume that can be tested before it reaches a plant. Injection is cheaper and smaller; batch tanks allow per-room recipes and verification.
Do I need batch tanks for commercial cannabis?
Not always. Batch tanks earn their cost in multi-room facilities that run different feeds to different rooms on the same day, and in operations that test every batch before feeding. A single recipe facility with tight water room space is usually better served by inline injection.
How many batch tanks does a facility need?
The sample system runs six 300 gallon tanks across mothers, veg and four flower rooms. The count follows how many rooms need to be fed differently at the same time, not the floor area.
Can a facility use both?
Yes, and many do. The sample approval set carries an inline Dosatron sheet alongside a batch tank P&ID, because propagation and mothers are often injected while flower runs from batch.
How we put this together
The comparison is of the two methods as they are drawn in EES sets: the sample P&ID uses batch tanks fed from a fertigation skid, and a separate sheet in the approval set covers inline Dosatron injection. The trade-offs described are operational consequences of how each method works, not tested performance figures.
Elevated designs and supplies both. This page describes how each behaves rather than recommending one for every facility.